STANDARD C520    -     Keypad Guide
|----------------------------------------------------------------------------|
|Key |  Alone  |   With "FUNC" key  |  Key alone in set  |In Set With "F"    |
|----------------------------------------------------------------------------|
| 0  |    0    |Enter Set Mode      |Mute keypad bleep   |Set Band Edge Limit|
|    |         |                    |                    |xyzt:VHF 1xy to 1zt|
| 1  |    1    |PTT Lock            |-                   |Tx DelayON repeater|
|    |         |                    |                    |                   |
| 2  |    2    |Dual Watch. In Mem o|1kHz entry on keypad|Match CTCSS on scan|
|    |         |scanMem: VFO,FUNC+2 |                    |                   |
| 3  |    3    |Output Power L/M/H  |-                   |Switch UHF Bands   |
|    |         |                    |                    |                   |
| 4  |    4    |Frequency Lock      |Mute noise while sql|Input 4 or 3 digits|
|    |         |                    |                    |                   |
| 5  |    5    |Battery Saver       |Auto power off 30min|-                  |
|    |         |                    |                    |                   |
| 6  |    6    |Select Step Size    |Enable tune in lock |Fast tune 1MHz/100k|
|    |         |                    |                    |                   |
| 7  |    7    |CTCSS select TX/RX  |CTCSS tone frequency|-                  |
|    |         |                    |                    |                   |
| 8  |    8    |Repeater Shift +/-  |Set shift freq, over|Cross Band Repeater|
|    |         |                    |10MHz set with tune |                   |
| 9  |    9    |Reverse Repeat Shift|Make LAMP button REV|Up/Dn keys do 10MHz|
|    |         |                    |                    |                   |
| *  |Step Down|Search up, then 0 if|                    |                   |
|    |         |Busy or Pause scan  |                    |                   |
| #  |Step Up  |Memory Shift        |                    |                   |
|    |         |                    |                    |                   |
| A  |Cancel   |                    |                    |                   |
|    |         |                    |                    |                   |
| B  |Pager On |Set Pager Codes     |                    |                   |
|    |         |                    |                    |                   |
| C  |Mem Scan |Partial Memory Scan,|                    |                   |
|    |         |only M°: VFO,Func+C |                    |                   |
| D  |Dial/Mem |Store Dial In Memory|                    |                   |
|    |         |                    |                    |                   |
|Lamp|auto 5sec|light on/off        |                    |                   |
|    |         |                    |                    |                   |
|Sqlc|set squlc|                    |                    |                   |
|    |         |                    |                    |                   |
|Call|1750 Hz  |                    |                    |                   |
|    |         |                    |                    |                   |
|Rst |reset all|                    |                    |                   |
|    |         |                    |                    |                   |
|Tune|up/down  |up/down 100/1000 kHz|                    |                   |
|----------------------------------------------------------------------------|
|To add 820-900,900-980 band in UHF: UHF F+L F+0 F+B F+L F+3 A               |
|----------------------------------------------------------------------------|
|Scan between 2 memory Mx and My: Mem mode, FUNC * when Mx, then press y (My)|
|----------------------------------------------------------------------------|
|To remove frequency from memory: [n°mem]+A A                                |
|----------------------------------------------------------------------------|
|SET +/- indipendent RX/TX freq. in memory number [n°mem]                    |
|- In VFO mode it fixes RX freq: F+D [n°mem]                                 |
|- In VFO mode it fixes TX freq: F+D F+A [n°mem]                             |
|----------------------------------------------------------------------------|
|ACTIVATE +/- indipendend RX/TX freq. in mem: F+D F+[n°mem] (it appears +/-) |
|DISABLE  +/- indipendend RX/TX freq. in memory number [n°mem]               |
|- delete n°mem: [n°mem]+A A                                                 |
|- set new freq. in n°mem'; set new freq. in n°mem                           |
|- delete n°mem' if unwanted                                                 |
|----------------------------------------------------------------------------|
Writed by: NICOLA IV3WHU - JN65TS - 14 Feb 2002
Address: P.O.BOX 3717 - 34011 AURISINA TS - ITALY
Email: iv3whu**NOSPAM**@amsat.org - Web: www.qsl.net/iv3whu
Packet: IV3WHU**NOSPAM**@IR3IP.AMPR.ORG
HamBBS Mail: IV3WHU@IK3GET.IVEN.ITA.EU
[Correct view]: use fixed sized font (example: Lucida Console 10).       -END-